Catégories
Chercher
Critères de recherche
Produits répondant aux critères de recherche
Arduino Wemos D1 (Wemos D1)
Based on ESP-8266EX
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
Shield clavier LCD pour Arduino (oh-arduino-lcd1602keypad)
- 16x2 LCD & keypad shield for
- Utilizes the extremely common HD44780 parallel interface chipset
- Interface code is freely available
- uses 4 Bit For Arduino LCD Library
- Blue Backlight with white words (screen contrast adjustment)
- Reset button
- Its Up, Down, Left, Right buttons use only one analog input
- Size:8cm x 5.9cm - 3.15inch x 2.32inch
Arduino Easy Module Shield v1 (Arduino Easy Module Shield v1)
- Exemples d'utilisation (lien)
- Schéma (jpg)
- Compatible Arduino
- 2 boutons poussoir
- 2 Led (rouge et bleue)
- 1 Led RGB
- 1 récepteur infrarouge
- 1 capteur de luminosité - Photorésistance
- 1 capteur de température - LM35D
- 1 buzzer passif
- 1 potentiomètre rotatif
- 1 capteur d'humidité - DHT11
- 1 connecteur pour interface I2C
- 1 port série TTL
- 1 connecteur pour un signal analogique en lecture
- 1 bouton reset
Arduino Multi-function Shield (arduino-shield-multifunction-type1)
The multifunction shield features some most useful electronics divided into segments:
- Four LEDs
- Three pushbuttons
- A reset button
- A piezo-buzzer
- An LED display module (four-digit, seven-segment)
- Two serial LED display driver ICs(74HC595)
- A multi-turn trimpot (10K)
- A port for DS18B20 temperature sensor
- A port for TSOP1838 infrared receiver module
- A APC220 wireless module interface (serial/UART interface)
Arduino Proto Shield SYB-170 (oh-arduino-proto-shield)
- Small soldering area.
- All Arduino pins are brought to the top level.
- 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
- 5V, GND, and Raw pins are exposed as well.
- SOIC place for IC.
- The mini breadboard has 170 tie points.
- The breadboard sticks on the prototype shield with its self-adhesive backing.
- Prototype Size:7cm x 5.5cm x 2cm
- Mini breadboard size: 4.4 * 3.4 * 1cm
Module capteur avec microphone KY-038 (KY-038)
Le capteur KY-038 permet de détecter la présence d'un niveau sonore, ajustable via un potentiomètre.
- DO (Sortie numérique) : signal présent si la limite fixée par le potentiomètre est atteinte
- AO (Sortie analogique) : mesure directe de la tension à la sortie du micro
- L1 : Indique que le capteur est alimenté
- L2 : Indique qu'un son est détecté
Tension | 3.3Vdc à 5Vdc |
Bande de fréquence | 50 HZ à 20Khz |
Impédance | 2.2Kohms |
Sensibilité | 48 à 66 dB |
Dimension | 44 x 15 x 10 mm |
Shield contrôle de moteur L293D compatible avec Arduino (L293D-SHIELD-001)
- 2*5V servo motor (servo) port is coupled to its high-resolution high-precision timer - no jitter
- Up to four bi-directional DC motor and 4 PWM speed (about 0.5% resolution)
- Up to 2 stepper motor control, single / double-step control, staggered or micro-step and the rotation angle control
- 4-channel H-bridge: L293D each bridge chip provides .0.6 A (peak 1.2A) current and with thermal shutdown protection, 4.5V to 36V
- Large terminal terminals make wiring easier (10 - 22AWG) and power supply
Arduino micro ATMEGA32U4 5V (oh-arduino-micro-atmega32u4-5v)
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Ressources :
Boitier pour Arduino (oh-arduino-case-clear)
- En acrylique transparent
- Compatible avec Arduino UNO
- 6cm x 7.5cm x 1.7cm
UNO R3 (Clone Arduino 100% compatible) (UNO R3)
Description
- Clone du Arduino UNO R3 avec le Atmega328P en version DIP et le Atmega16U2 pour la liaison USB
- Révision 3
- 100% compatible - aucun pilote différent
- Expédié avec un petit câble USB
- Pour plus d’information sur cette carte :https://store.arduino.cc/usa/arduino-uno-rev3
Arduino micro ATMEGA32U4 5V avec header soudés et câble USB (oh-arduino-micro-atmega32u4-5v-ASBLY-Cable)
Version assemblée (connecteurs soudés).
Câble USB de 80cm inclus
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Version assemblée (connecteurs soudés).
Câble USB de 80cm inclus
Ressources :
- 1