Search
Search Criteria
Products meeting the search criteria
Arduino Wemos D1 (Wemos D1)
Based on ESP-8266EX
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
Arduino LCD shield with keypad (oh-arduino-lcd1602keypad)
- 16x2 LCD & keypad shield for
- Utilizes the extremely common HD44780 parallel interface chipset
- Interface code is freely available
- uses 4 Bit For Arduino LCD Library
- Blue Backlight with white words (screen contrast adjustment)
- Reset button
- Its Up, Down, Left, Right buttons use only one analog input
- Size:8cm x 5.9cm - 3.15inch x 2.32inch
Arduino Easy Module Shield v1 (Arduino Easy Module Shield v1)
- Examples of uses (lien)
- Module schematic (jpg)
- Arduino compatible
- 2 push-button
- 2 Led (red and blue)
- 1 Led RGB
- 1 IR receiver
- 1 Brightness sensor module
- 1 LM35D temperature sensor module
- 1 Passive buzzer module
- 1 Rotary potentiometer module
- 1 DHT11 temperature and humidity sensor module
- 1 I2C interface (A4 SDA, A5 SCL)
- 1 TTL serial port
- 2 channel digital ports (D7, D8)
- 1 channel analog port (A3)
- 1 Reset button
Arduino Multi-function Shield (arduino-shield-multifunction-type1)
The multifunction shield features some most useful electronics divided into segments:
- Four LEDs
- Three pushbuttons
- A reset button
- A piezo-buzzer
- An LED display module (four-digit, seven-segment)
- Two serial LED display driver ICs(74HC595)
- A multi-turn trimpot (10K)
- A port for DS18B20 temperature sensor
- A port for TSOP1838 infrared receiver module
- A APC220 wireless module interface (serial/UART interface)
Arduino Proto Shield SYB-170 (oh-arduino-proto-shield)
- Small soldering area.
- All Arduino pins are brought to the top level.
- 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
- 5V, GND, and Raw pins are exposed as well.
- SOIC place for IC.
- The mini breadboard has 170 tie points.
- The breadboard sticks on the prototype shield with its self-adhesive backing.
- Prototype Size:7cm x 5.5cm x 2cm
- Mini breadboard size: 4.4 * 3.4 * 1cm
Sound sensor module KY-038 (KY-038)
- High sensitivity sound detection module with 2 Outputs (1 analog and 1 digital)
- Voltage: 3.3 to 5 VDC
- Frequency response: 50 Hz - 20 KHz
- Sensitivity: 48 - 66 dB
Voltage | 3.3Vdc to 5Vdc |
Frequency response | 50 HZ to 20Khz |
Impedance | 2.2Kohms |
Sensitivity | 48 to 66 dB |
Dimensions | 44 x 15 x 10 mm |
L293D Motor Driver Board for Arduino Motor Expansion Board Arduino (L293D-SHIELD-001)
- 2*5V servo motor (servo) port is coupled to its high-resolution high-precision timer - no jitter
- Up to four bi-directional DC motor and 4 PWM speed (about 0.5% resolution)
- Up to 2 stepper motor control, single / double-step control, staggered or micro-step and the rotation angle control
- 4-channel H-bridge: L293D each bridge chip provides .0.6 A (peak 1.2A) current and with thermal shutdown protection, 4.5V to 36V
- Large terminal terminals make wiring easier (10 - 22AWG) and power supply
Arduino Micro ATMEGA32U4 5V (oh-arduino-micro-atmega32u4-5v)
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Ressources :
Arduino Uno R3 Case Enclosure (oh-arduino-case-clear)
- Transparent Acrylic Box
- Compatible for arduino UNO R3
- 6cm x 7.5cm x 1.7cm
UNO R3 (100% compatible Arduino clone) (UNO R3)
Description
- Clone of the Arduino UNO R3
- Revision 3
- 100% compatible version with Atmega16U2 USB link
- Shipped with a 30cm USB cable
- For more informations :https://store.arduino.cc/usa/arduino-uno-rev3
Arduino Micro Atmega32u4 with soldered headers and USB cable (oh-arduino-micro-atmega32u4-5v-ASBLY-Cable)
Fully assembled version (headers soldered)
Also include a 80cm USB cable.
Ressources :
Microcontroller | ATmega32U4 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limit) | 6-20V |
Digital I/O Pins | 20 |
PWM Channels | 7 |
Analog Input Channels | 12 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 32 KB (ATmega32U4) of which 4 KB used by bootloader |
SRAM | 2.5 KB (ATmega32U4) |
EEPROM | 1 KB (ATmega32U4) |
Clock Speed | 16 MHz |
LED_BUILTIN | 13 |
Length | 48 mm |
Width | 18 mm |
Weight | 13 g |
Fully assembled version (headers soldered)
Also include a 80cm USB cable.
Ressources :
- 1