Controller

Sort By:  
Arduino Wemos D1 (Wemos D1)
Based on ESP-8266EX
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
11.95$
ATCURL35100 (ATCURL35100)
Development board based on the AT90USB1287

Features :
  • 2 Full H-Brides (L293)
  • On board 5Vdc regulator
  • On board 16Mhz crystal
  • 2 push button (reset and user)
  • 2 Leds (power and user)
  • UBS OTG capable
  • All I/O are protected (diode and resistor)
  • Use JST connector
79.95$
Arduino Uno R3 Case Enclosure (oh-arduino-case-clear)
  • Transparent Acrylic Box
  • Compatible for arduino UNO R3
  • 6cm x 7.5cm x 1.7cm
5.95$
Arduino Proto Shield SYB-170 (oh-arduino-proto-shield)
  • Small soldering area.
  • All Arduino pins are brought to the top level.
  • 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
  • 5V, GND, and Raw pins are exposed as well.
  • SOIC place for IC.
  • The mini breadboard has 170 tie points.
  • The breadboard sticks on the prototype shield with its self-adhesive backing.
  • Prototype Size:7cm x 5.5cm x 2cm
  • Mini breadboard size: 4.4 * 3.4 * 1cm
4.95$
ESP32 DEVKIT V1 Board (Wi-Fi and Bluetooth) (oh-esp32-devkit-board)
  • This is an Arduino IDE comptabile development board
  •  Processors:
    • CPU: Xtensa dual-core (or single-core) 32-bit LX6 microprocessor, operating at 160 or 240 MHz and performing at up to 600 DMIPS
    • Ultra low power (ULP) co-processor
  • Memory: 520 KiB SRAM
  • Wireless connectivity:
    • Wi-Fi: 802.11 b/g/n
    • Bluetooth: v4.2 BR/EDR and BLE
  • Peripheral interfaces:
  • Security:
  • Power management:
    • Internal low-dropout regulator
    • Individual power domain for RTC
    • 5μA deep sleep current
    • Wake up from GPIO interrupt, timer, ADC measurements, capacitive touch sensor interrupt
12.95$
Arduino UNO R3 (UNO R3)

Description

12.95$
Arduino Micro Atmega32u4 with soldered headers and USB cable (oh-arduino-micro-atmega32u4-5v-ASBLY-Cable)
MicrocontrollerATmega32U4
Operating Voltage5V
Input Voltage (recommended)7-12V
Input Voltage (limit)6-20V
Digital I/O Pins20
PWM Channels7
Analog Input Channels12
DC Current per I/O Pin20 mA
DC Current for 3.3V Pin50 mA
Flash Memory32 KB (ATmega32U4) of which 4 KB used by bootloader
SRAM2.5 KB (ATmega32U4)
EEPROM1 KB (ATmega32U4)
Clock Speed16 MHz
LED_BUILTIN13
Length48 mm
Width18 mm
Weight13 g

Fully assembled version (headers soldered)
Also include a 80cm USB cable.

Ressources : 
17.95$
Arduino Micro ATMEGA32U4 5V (oh-arduino-micro-atmega32u4-5v)
MicrocontrollerATmega32U4
Operating Voltage5V
Input Voltage (recommended)7-12V
Input Voltage (limit)6-20V
Digital I/O Pins20
PWM Channels7
Analog Input Channels12
DC Current per I/O Pin20 mA
DC Current for 3.3V Pin50 mA
Flash Memory32 KB (ATmega32U4) of which 4 KB used by bootloader
SRAM2.5 KB (ATmega32U4)
EEPROM1 KB (ATmega32U4)
Clock Speed16 MHz
LED_BUILTIN13
Length48 mm
Width18 mm
Weight13 g

Ressources : 
13.95$
Per Page      1 - 8 of 8
  • 1