Robots

• 2 Full H-Brides (L293)
• On board 5Vdc regulator
• On board 16Mhz crystal
• 2 push button (reset and user)
• 2 Leds (power and user)
• UBS OTG capable
• All I/O are protected (diode and resistor)
• Use JST connector

• Anodized aluminum robot frame with 2 motors and 2 wheels
• Includes 2 wheels and 1 universal wheel
• Can be used with Arduino or Raspberry Pi with the motor shield or hat

• 2 x Motors FT90R-W
• 2 x FT-DC-W wheel
• 1 x Floor Frame (in anodized aluminum)
• 1 x Universal wheel
• 1 x Screw kit

• 100mm x 80mm x 27mm
• Wheel diameter = 60mm

• L298 datasheet (PDF)
• Module schematic (PDF)
• Arduino motor shield rev 3
• Based on a L298
• 2A per Ch (4A peak)
• Able to control 2 DC motors or 1 step motor
• Current sensing (1.65V/A)
• Supply 5 à 12V
• 4 headers for servo motor
• 2 headers for I2C connection
• Output status on LEDs

• Datasheet (PDF)
• 1.5A per ch (2.5A peak)
• Thermal protection
• Supply 2V à 10V
• Input levels 1.8V à 7V

• Input voltage : 3.2 to 40 Vdc
• Driver : L298N (Dual H Bridge)
• Power-supply: 5V à 35V
• Peak current : 2A
• Size: 3.4cm x 4.3cm x 2.7cm
• On-board 5V reulated output supply

Features 

Can be reprogram by FEETECH programmer

Easy to control 2CH DC motor 

Control DC motor to bidirectional continuous rotation 

The speed is linear response to PWM 

Accepts four mounting screws 

Easy to interface with any Arduino microcontroller or PWM-capable device 

Weighs only 3.5 g

Apply to kinds of small mobile platform robot

Specification 

Weight: 3.5g

Dimension (L*W*H): 34mm * 25mm * 7.5mm

Controller: STM8F003F3P6

Working Voltage Range: 4V~9V (2CH + and – connect together) 

Recommended Voltage: 6V 

IDLE Current: 10Ma

1CH Continuous Load Current: 1.3A 

Working Temperature: -5℃~60℃

• Small soldering area.
• All Arduino pins are brought to the top level.
• 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
• 5V, GND, and Raw pins are exposed as well.
• SOIC place for IC.
• The mini breadboard has 170 tie points.
• The breadboard sticks on the prototype shield with its self-adhesive backing.
• Prototype Size:7cm x 5.5cm x 2cm
• Mini breadboard size: 4.4 * 3.4 * 1cm

• Package Included:

  1 x Car chassis
  2 x Gear motor (1:48)
  2 x Car tire
  2 x Speed encoder
  4 x Fastener
  1 x Universal wheel
  1 x Battery box(batteries not included)
  1 x Screwdriver
  All necessary screw and nut.

• TB6612FNG Datasheet (PDF)
• Schematic (PDF)
• Adopted ceramic capacitor, it has a more stable performance
• The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak)
• Built-in thermal shutdown circuit and low voltage detecting circuit
• CW/ CCW/ short brake/ stop motor control modes

• Anodized aluminum mini robot frame with 2 motors and 2 wheels
• Drive motors with 3-6VDC, 200-400mA run, 1.5A hard stall
• Includes 2 wheels and 1 plastic caster ball
• Can be used with Arduino or Raspberry Pi with the motor shield or hat

• 2 x 130 DC motor gear box
• 2 x FT-DC-W wheel
• 2 x Floor Frame (in anodized aluminum)
• 2 x DC bracket
• 1 x Bull 's-eye bearing wheel
• 1 x Screw kit

• 100mm x 80mm x 27mm
• Wheel diameter = 60mm

• Anodized aluminum mini robot frame with 4 motors and 4 wheels
• Includes 4 wheels 
• Can be used with Arduino or Raspberry Pi with the motor shield or hat

• 4 x Motors FT90R-W
• 2 x FT-DC-W wheel
• 1 x Floor Frame (in anodized aluminum)
• 1 x Screw kit

• 170mm x 100mm x 60mm
• Wheel diameter = 60mm

Description

• Clone of the Arduino UNO R3
• Revision 3
• 100% compatible version with Atmega16U2 USB link
• Shipped with a 30cm USB cable
• For more informations :https://store.arduino.cc/usa/arduino-uno-rev3