Actuators

Features:

• Submersible water pump, it is great for experiment, aquarium, and fountain etc
• Micro delicate appearance
• Big flow rate that can be 100L/H
• Continuous service life of up to more than 200 hours
• Suitable for varieties of water such as city water, groundwater, sea water

Specifications:

• Material: Plastic + Electronic Components
• Size:  Approx. 4.5cm x 2.3cm x 3.2cm / 1.7 inch x 0.9 inch x 1.2 inch (Length x width x Height)
• Power: 3W
• Voltage: DC 3-4.5V  ( Please keep off over-voltage)
• Current: within 0.05A
• Flow Rate: 100 L/H
• Water Temperature: -20°C~50°C
• Type: Submersible Water Pump
• Use Silicone tube of 6mm inner diameter

Features:

• Submersible water pump, it is great for experiment, aquarium, and fountain etc
• Micro delicate appearance
• Big flow rate that can be 120L/H
• Continuous service life of up to more than 200 hours
• Suitable for varieties of water such as city water, groundwater, sea water

Specifications:

• Material: Plastic + Electronic Components
• Size:  Approx. 4.5cm x 2.3cm x 3.2cm / 1.7 inch x 0.9 inch x 1.2 inch (Length x width x Height)
• Power: 3W
• Voltage: DC 3-4.5V  ( Please keep off over-voltage)
• Current: within 0.05A
• Flow Rate: 120 L/H
• Water Temperature: -20°C~50°C
• Type: Submersible Water Pump
• Use Silicone tube of 6mm inner diameter

• Module schematic (PNG)
• Wiki for more informations (LIEN)
• 5V activated relay
• Can be activated directly from a microcontroler, or an Arduino
  • Activation current 15 to 20 mA
• 4x relay AC250V 10A / DC30V 10A
• Each relay has an LED to show the state of the relay

• Equipped with a silicone tire
• Press-fit design to make connecting to your FS90R Micro Servo
• Super quick and easy to connect
• Wheels are 8mm wide
• Wheels diameter is 60mm (2.4inches)
• 2 additionnals mounting holes ease mounting on differents hubs

• Equipped with a silicone tire
• Press-fit design to make connecting to your FS90R Micro Servo
• Super quick and easy to connect
• Wheels are 8mm wide
• Wheels diameter is 60mm (2.4inches)
• 2 additionnals mounting holes ease mounting on differents hubs

• Voltage range : 3 à 6V
• Courant continu : 150 to 200mA
• Speed : 130RPM at 3V

• Dimensions: 32.3mm x 12.3mm x 29.9mm / 1.3" x 0.49" x 1.2"
• Spline Count: 21
• Weight: 8.4g
• No load speed: 110RPM (4.8v) / 130RPM (6v)
• Running Current (at no load): 100mA (4.8v) / 120mA (6v)
• Peak Stall Torque (4.8v): 1.3 kg/cm / 18.09 oz/in
• Peak Stall Torque (6v): 1.5 kg/cm / 20.86 oz/in
• Stall Current: 550mA (4.8v) / 650mA (6v)

• L298 datasheet (PDF)
• Module schematic (PDF)
• Arduino motor shield rev 3
• Based on a L298
• 2A per Ch (4A peak)
• Able to control 2 DC motors or 1 step motor
• Current sensing (1.65V/A)
• Supply 5 à 12V
• 4 headers for servo motor
• 2 headers for I2C connection
• Output status on LEDs

• Datasheet (PDF)
• 1.5A per ch (2.5A peak)
• Thermal protection
• Supply 2V à 10V
• Input levels 1.8V à 7V

• Input voltage : 3.2 to 40 Vdc
• Driver : L298N (Dual H Bridge)
• Power-supply: 5V à 35V
• Peak current : 2A
• Size: 3.4cm x 4.3cm x 2.7cm
• On-board 5V reulated output supply