WiFi

Sort By:  
Arduino Wemos D1 (Wemos D1)
Based on ESP-8266EX
For Arduino compatible, using For Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use For Arduino IDE development, the same operation For Arduino UNO
USB CHIP CH340
11.95$
ESP-01 (ESP8266) (oh-esp01)
  • WiFi Module can easily give any microcontroller access to your WiFi network.
  • Run out of the box that just simply hook this up to your Arduino device and get about as much WiFi-ability as a WiFi Shield offers.
  • Supports APSD for VoIP applications and Bluetooth co-existance interfaces.
  • Contains a self-calibrated RF allowing it to work under all operating conditions, and requires no external RF parts.
  • This module has a powerful enough on-board processing and storage capability.
6.95$
ESP-01S (ESP8266) (oh-esp01S)

The ESP-01S ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each ESP-01S ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much WiFi-ability as a WiFi Shield offers (and that’s just out of the box)! The ESP-01S ESP8266 module is an extremely cost effective board with a huge, and ever growing, community.

This module has a powerful enough on-board processing and storage capability that allows it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, is designed to occupy minimal PCB area. The ESP8266 supports APSD for VoIP applications and Bluetooth co-existance interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions, and requires no external RF parts.

Features:

  • 802.11 b/g/n
  • Wi-Fi Direct (P2P), soft-AP
  • Integrated TCP/IP protocol stack
  • Integrated TR switch, balun, LNA, power amplifier and matching network
  • Integrated PLLs, regulators, DCXO and power management units
  • +19.5dBm output power in 802.11b mode
  • Power down leakage current of <10uA
  • 1MB Flash Memory
  • Integrated low power 32-bit CPU could be used as application processor
  • SDIO 1.1 / 2.0, SPI, UART
  • STBC, 1×1 MIMO, 2×1 MIMO
  • A-MPDU & A-MSDU aggregation & 0.4ms guard interval
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)

Documents:

6.95$
ESP32 DEVKIT V1 Board (Wi-Fi and Bluetooth) (oh-esp32-devkit-board)
  • This is an Arduino IDE comptabile development board
  •  Processors:
    • CPU: Xtensa dual-core (or single-core) 32-bit LX6 microprocessor, operating at 160 or 240 MHz and performing at up to 600 DMIPS
    • Ultra low power (ULP) co-processor
  • Memory: 520 KiB SRAM
  • Wireless connectivity:
    • Wi-Fi: 802.11 b/g/n
    • Bluetooth: v4.2 BR/EDR and BLE
  • Peripheral interfaces:
  • Security:
  • Power management:
    • Internal low-dropout regulator
    • Individual power domain for RTC
    • 5μA deep sleep current
    • Wake up from GPIO interrupt, timer, ADC measurements, capacitive touch sensor interrupt
12.95$
Per Page      1 - 4 of 4
  • 1